"How To Check The Hours Used on Your Plasma" : - Home Theater Forum and Systems - HomeTheaterShack.com

Reply
 
Thread Tools
post #1 of 32 Old 12-05-09, 06:16 PM Thread Starter
Shackster
 
BruZZi's Avatar
BruZZi
 
Join Date: Jul 2008
Location: NEW YORK
Posts: 60

How To Check The Hours
Used on Your Plasma






01) Panasonic Consumer Models
02) Panasonic Commercial Models
03) Panasonic VX100 Series
04) Panasonic Foreign Models


05) Fujitsu
06) Hitachi
07) HP
08) LG / Zenith
09) Pioneer
10) Samsung












Panasonic
Consumer Models



2011 Models : _X3 / S30 / ST30 / GT30 / VT30
2010 Models : _X24 / C2 / U2 / S2 / G20 / G25 / GT20 / GT25 / VT20 / VT25


  • Press and hold the {VOL -} button ON THE PLASMA TV.
  • Then press the {INFO} button on the remote control 3 times.

  • "Start Adjustment Menu" message will be displayed followed
    by the Service Menu after few seconds.

    • ADJUST {Picture Adjustment}
    • WB-ADJUST {White Balance Adjustment}
    • OPTION {Option Setting}
    • V-SUS {V-SUS Adjustment}
    • AGING
    • SRV-TOOL {Service Tool}
    {1} & {2} buttons move through options

  • Press the {2} button once to select "SRV-TOOL".

  • Then press the {OK} button to access it.

  • Using the cursor keys, highlight the right side
    of the last item "PTCT :00.00.00.00.00" :





  • Then press and hold the {MUTE} button for 3 seconds.

  • Time and Count will be displayed in red color:



    __TIME = Hours : Minutes of operation.
    COUNT = Times the Plasma was powered on.

  • To exit, unplug the power cable.

<<<<<<<<<< WARNING BY BRUZZI >>>>>>>>>>
The {VOL+} & {VOL-} buttons are used to change values
while in the Service Menu. Make sure not to touch those
buttons anytime while checking the hours used.


===========================================================================



2009 Models : _ PX14 / PS14 / C1 / U1 / X1 / S1 / G10 / G15 / V10 / Z1
2008 Models : _ PX80U / PZ80U / PZ85U / PZ800U / PZ850U



  • TC-P54Z1: Press and hold the {VOL -} button ON MEDIA RECEIVER.
    All Other: Press and hold the {VOL -} button ON THE PLASMA TV.

  • Then press the {INFO} button on the remote control 3 times.

  • The Service Menu will be displayed with the following options:

    • ADJUST {Picture Adjustment}
    • WB-ADJUST {White Balance Adjustment}
    • OPTION {Option Setting}
    • V-SUS {V-SUS Adjustment}
    • AGING
    • SRV-TOOL {Service Tool}
    {1} & {2} buttons move through options

  • Press the {2} button once to select "SRV-TOOL".

  • Then press the {OK} button to access it.

  • Using the cursor keys, highlight the right side
    of the last item "PTCT :00.00.00.00.00" :





  • Then press and hold the {MUTE} button for 3 seconds.

  • Time and Count will be displayed in red color:



    __TIME = Hours : Minutes of operation.
    (On older firmware(s), hours shown must be divided by 256 for correct value)

    COUNT = Times the Plasma was powered on.

  • To exit, unplug the power cable.

<<<<<<<<<< WARNING BY BRUZZI >>>>>>>>>>
The {VOL+} & {VOL-} buttons are used to change values
while in the Service Menu. Make sure not to touch those
buttons anytime while checking the hours used.


===========================================================================



2007 Models : _ PE77U / PX75U / PX77U / PZ77U / PZ700U / PZ750U


  • Press and hold the {VOL -} button ON THE PLASMA TV.
  • Then press the {RECALL} button on the remote control 3 times.

  • The Service Menu will be displayed with the following menus:

    • ADJUST (PICTURE ADJUSTMENT)
    • WB-ADJUST (WHITE BALANCE ADJUSTMENT)
    • OPTION (OPTION SETTING)
    • AGING
    • RM-SET (REMOTE CONTROL CODE SETTING)
    • SRV-TOOL (SERVICE TOOL)
    {1} & {2} buttons move through menus

  • Press the {2} button once to select "SRV-TOOL".

  • Then press the {OK} button to access it.

  • Using the cursor keys, select the right side
    of the last option "PTCT :00.00.00.00.00" :





  • Then press and hold the {MUTE} button for 3 seconds.

  • Time and Count will be displayed in red color.





    TIME = Hours : Minutes of operation.
    COUNT = Times the Plasma was powered on.

  • To exit, unplug the power cord.

<<<<<<<<<< WARNING BY BRUZZI >>>>>>>>>>
The {VOL+} & {VOL-} buttons are used to change values
while in the Service Menu. Make sure not to touch those
buttons anytime while checking the hours used.


===========================================================================



2006 Models : _ PD60U / PX6U / PX60U / PX600U
2005 Models : _ PD50U / PX50U / PX500U


  • Press and hold the {VOL -} button ON THE PLASMA TV.
  • Then press the {RECALL} button on the remote control 3 times.

  • The Service Menu will be displayed.

  • Use the {1} or {2} buttons to select "Option".
  • Then press and hold the {MUTE} button on the remote for 3 seconds.

    TIME = Hours of Operation (Hex Numbers)
    COUNT = Times the Plasma was Powered On (Hex Numbers)

  • To exit, turn the power off.

Converting Hours in Hex to Dec Numbers:
In Windows, open CALC (calculator).
Click View, and set it to Scientific mode.
Select Hex, enter the number then click Dec.
It will convert it to a Decimal number for you.
< Tip by Jasonbanks >







Panasonic
Commercial Models





8UK / 9UK / 10UK / 11UK:

  • Press and hold the {VOL -} button ON THE PLASMA DISPLAY.

  • Then press the {STATUS} button 3 times on the remote.
    (Status button is the one above Setup button}

  • The Service Menu (CAT) will be displayed.
    (CAT = Computer Aided Test Menu)

  • Using the cursors keys on the remote, select "SD Mode".
  • And press the Action key { } to access it.

    On the MTBF (Mean Time Between Failure) parameter:

    WT = How many times the unit was powered on
    PT = The cumulative time in hours

  • To exit the SD Mode, press the {R} button.
  • To exit the CAT menu, press the {STATUS} button.
  • To completely exit the Service Menu, turn the power off.



===========================================================================



3UY / 4UY / 5UY / 6UY / 7UY:

  • Press and hold the {VOL -} button ON THE PLASMA DISPLAY.

  • Then press the {STATUS} button 3 times on the remote.
    (Status button is the one below Power button}

  • The Service Menu (CAT) will be displayed.
    (CAT = Computer Aided Test Menu)

  • Using the cursors keys on the remote, select "SD Mode".
  • And press the Action key { } to access it.

    On the MTBF (Mean Time Between Failure) parameter:

    WT = How many times the unit was powered on
    PT = The cumulative time in hours

  • To exit the SD Mode, press the {R} button.
  • To exit the CAT menu, press the {STATUS} button.
  • To completely exit the Service Menu, turn the power off.








Panasonic
Premiere Models





VX100U / VX100E :

  • Press and hold the {VOL -} button ON THE PLASMA DISPLAY.

  • Then press the {RECALL} button 3 times on the remote.

  • The Service Menu (CAT) will be displayed.
    (CAT = Computer Aided Test Menu)

  • Using the cursors keys on the remote, select "SD Mode".
  • And press the {OK} button to access it.

    On the MTBF (Mean Time Between Failure) parameter:

    WT = How many times the unit was powered on
    PT = The cumulative time in hours

  • To exit the SD Mode, press the {R} button.
  • To exit the CAT menu, turn the power off.








Panasonic
European Models





PZ80 / PZ81 / PZ82 / PZ85 / PZ800
PX8 / PX80 / PX81 :


  • Press and hold the {VOL -} button ON THE PLASMA TV.
  • Then press the {0} button 3 times on the remote.

  • The Service Menu will come up.

  • The hours used will be displayed in the right lower corner.

    TIME : Hours and minutes of operation
    COUNT : Times the Plasma was powered on


  • To exit, press the {EXIT} button or turn the power off.



===========================================================================



PV7 / PV70 / PV71 / PZ700
PX7 / PX70 / PX71 / PX72 :


  • Press and hold the {VOL -} button ON THE PLASMA TV.
  • Then press the {0} button 3 times on the remote.

  • The Service Menu will come up.

  • The hours used will be displayed in the right lower corner.

    TIME : Hours and minutes of operation
    COUNT : Times the Plasma was powered on


  • To exit, press the {EXIT} button or turn the power off.



===========================================================================



Previous Models :

  • Set the channel to CH99.
  • Select the EQ 12kHz.
  • Press the {HOLD} button on the remote control.
  • The Service Menu 2 will be displayed.

  • Using the {GREEN} button on the remote,
    scroll down to the last Option Menu: "Hours".

  • To exit, press {EXIT} or turn the power off.








Fujitsu
Consumer Models



  • Press and hold the {ENTER} button on the remote
    until the Service Menu is displayed:

    • Monitor Mode A
    • Monitor Mode B
    • Extend Adjust

  • Select "Monitor Mode A" and press {ENTER} to access it.

    Hours Meter:

    To determine total hours, add RGB and video for the total hours on the plasma
    (each number represents hours on that selected input).
    Disregard total hours. That's the number of hours the Plasma is plugged in.

  • To exit, turn the power off.








Hitachi
Consumer Models





HDS69 / HDT79 / HDX99 :


  • Using the remote, press the following buttons:
    {MENU}, {MENU}, {8} & {SELECT}

  • The Service Menu will be displayed.

  • Use the {UP} or (DOWN} buttons to select "PDP"
  • The press the {SELECT} buton to access it.
  • Hours used will be shown in the "OPERATION TIME"

  • To exit, turn the power off.








HP
Consumer Models




PE-4200N / PL-4200N / PL-5000N
( Rebadged Panasonic PX500 Series )


  • Press and hold the {VOL -} button ON THE PLASMA.
  • Then press the {RECALL} button on the remote control 3 times.

  • The Service Menu will be displayed.

  • Use the {1} or {2} buttons to select "Option".
  • Then press and hold the {MUTE} button on the remote for 3 seconds.

    TIME = Hours of Operation (Hex Numbers)
    COUNT = Times the Plasma was Powered On (Hex Numbers)

  • To exit, turn the power off.

Converting Hours in Hex to Dec Numbers:
In Windows, open CALC (calculator).
Click View, and set it to Scientific mode.
Select Hex, enter the number then click Dec.
It will convert it to a Decimal number for you.
< Tip by Jasonbanks >







LG / Zenith
Consumer Models





PG20 / PG25 / PG60 :


  • Press and hold the {VOL -} button on the remote.
  • Then press and hold the {MENU} button on the TV.

  • After the password screen comes up, press
    the following code: {0} {0} {0} {0}

  • The Service Menu will be displayed.

  • The hours used is shown after "UTT".

  • To exit, turn the power off.


    Info sent by crkpot








Pioneer
Consumer Models






5020FD / 6020FD
:



You cannot access the Service Menu on these models using their regular
remote controls. But there are other ways to check the hours used:

  1. Service Remote Control Models: GGF1589 or GGF1633

  2. Get ControlCAL and then follow these instructions:
    http://www.controlcal.com/forum/showthread.php?t=120




KRP-500M / KRP-600M
PRO-101FD / PRO-141FD
PRO-111FD / PRO-151FD
:



You cannot access the Service Menu on these models using their regular
remote controls. But there are other ways to check the hours used:

  1. Set up the Network and use the following address:
    http://<krp ip address>/cgi/service_right.cgi

  2. Service Remote Control Models: GGF1589 or GGF1633

  3. Get ControlCAL and then follow these instructions:
    http://www.controlcal.com/forum/showthread.php?t=120

  4. Get KuroReader


===========================================================================




4280HD / 5080HD :


  • Using the remote control:
  • Turn off the TV Guide feature.
  • Turn off the power to set the TV into standby mode.
  • Press the {DISPLAY} buton once and wait 4 seconds.
  • Then press {LEFT} {UP} {LEFT} {RIGHT} {POWER} buttons
    within 5 seconds.

  • The Plasma will turn on with the "Information" page displayed.
  • Use the {DOWN} button to select "Hours Meter"

    PANEL = Hours of operation.
    ...MTB = Hours the set has been plugged in.

  • To exit, turn the power off.



===========================================================================




4270HD / 4271HD / 5070HD / 5071HD
6070HD / 6071HD / 507PU / 607PU
:



  • Using the remote control:
  • Turn off the TV Guide feature.
  • Turn off the power to set the TV into standby mode.
  • Press the {DISPLAY} buton once and wait 4 seconds.
  • Then press {LEFT} {UP} {LEFT} {RIGHT} {POWER} buttons
    within 5 seconds.

  • The Plasma will turn on with the "Information" page displayed.
  • Use the {DOWN} button to select "Hours Meter"

    PANEL = Hours of operation.
    ...MTB = Hours the set has been plugged in.

  • To exit, turn the power off.



===========================================================================




4360HD / 5060HD
:


  • Using the remote control:
  • Turn off the TV Guide feature.
  • Turn off the power to set the TV into standby mode.
  • Press the {DISPLAY} buton once and wait 4 seconds.
  • Then press {LEFT} {UP} {LEFT} {RIGHT} {POWER} buttons
    within 5 seconds.

  • The Plasma will turn on with the "Information" page displayed.
  • Use the {DOWN} button to select "Hours Meter"

    PANEL = Hours of operation.
    ...MTB = Hours the set has been plugged in.

  • To exit, turn the power off.








Samsung
Consumer Models





2010 "C" Models
:


  • While the TV is in standby mode:
  • Press the {MUTE}, {1}, {8}, {2} & {POWER} buttons.

  • The TV will turn on with the Service Menu displayed.

  • Use the {UP} or {DOWN} buttons to select "SVC"
  • Then press the {ENTER} button to access it.

  • "PANEL DISPLAY TIME" will be one of the items listed.

  • To exit, press the {RETURN} button and/or turn the power off.


===========================================================================




B550 / B560 / B590 / B650 / B850 / B860
A450 / A550 / A650
:


  • While the TV is in standby mode:
  • Press the {MUTE}, {1}, {8}, {2} & {POWER} buttons.

  • The TV will turn on with the Service Menu displayed.

  • Use the {UP} or {DOWN} buttons to select "PDP OPTION"
  • Then press the {ENTER} button to access it.

  • "PANEL DISPLAY TIME" will be one of the items listed.

  • To exit, press the {RETURN} button and/or turn the power off.


    NOTE: After exiting, all picture settings will be reset to
    default values. So make sure to write down custom
    adjustments before accessing the Service Menu.



===========================================================================



  • While the TV is in standby mode:
  • Press the {MUTE}, {1}, {8}, {2} & {POWER} buttons.

  • The TV will turn on with the Service Menu displayed.

  • Use the {UP} or {DOWN} buttons to select "OPTION BYTE"
  • Then press the {ENTER} button to access it.

  • "PANEL DISPLAY TIME" will be one of the items listed.

  • To exit, press the {RETURN} button and/or turn the power off.


    NOTE: After exiting, all picture settings will be reset to
    default values. So make sure to write down custom
    adjustments before accessing the Service Menu.






Yamaha
Plasmas




PDM-1 - 50" Plasma Display
( Rebadged Panasonic PHD5 Series )


  • Press and hold the {VOL -} button ON THE PLASMA DISPLAY.

  • Then press the {STATUS} button 3 times on the remote.
    (Status button is the one below Power button}

  • The Service Menu (CAT) will be displayed.
    (CAT = Computer Aided Test Menu)

  • Using the cursors keys on the remote, select "SD Mode".
  • And press the Action key {} to access it.

    On the MTBF (Mean Time Between Failure) parameter:

    WT = How many times the unit was powered on
    PT = The cumulative time in hours

  • To exit the SD Mode, press the {R} button.
  • To exit the CAT menu, press the {STATUS} button.
  • To completely exit the Service Menu, turn the power off.







Last edited by mechman; 03-18-11 at 09:38 AM. Reason: updated information
BruZZi is offline  
Sponsored Links
Advertisement
 
post #2 of 32 Old 12-05-09, 07:09 PM
Elite Shackster
 
mechman's Avatar
Steve Mechelke -mech
 
Join Date: Feb 2007
Location: Empire Township, MN
Posts: 14,912
My System
mechman is offline  
post #3 of 32 Old 12-05-09, 07:15 PM Thread Starter
Shackster
 
BruZZi's Avatar
BruZZi
 
Join Date: Jul 2008
Location: NEW YORK
Posts: 60
Re: "How To Check The Hours Used on Your Plasma" :

Quote:
mechman wrote: View Post
Thanks for the info BruZZi!

You're Welcome.

I still have to add some info.

.
BruZZi is offline  
post #4 of 32 Old 12-05-09, 07:28 PM
HTS Administrator
 
lcaillo's Avatar
Tech Guru
 
Join Date: May 2006
Location: Gainesville, FL, USA
Posts: 10,991
Send a message via AIM to lcaillo
Re: "How To Check The Hours Used on Your Plasma" :

Nice job.

Looking for me, just google my username. I have used the same one for most sites for many years.
lcaillo is online now  
post #5 of 32 Old 12-08-09, 09:22 AM
Shackster
Robert
 
Join Date: Nov 2009
Location: mechanicsville , MD
Posts: 38
Re: "How To Check The Hours Used on Your Plasma" :

Do you have a web site to verify serial numbers of Pioneer 600m
So MD TopGun is offline  
post #6 of 32 Old 12-08-09, 09:25 AM
HTS Administrator
 
lcaillo's Avatar
Tech Guru
 
Join Date: May 2006
Location: Gainesville, FL, USA
Posts: 10,991
Send a message via AIM to lcaillo
Re: "How To Check The Hours Used on Your Plasma" :

No, I do not. What are you trying to verify?

Looking for me, just google my username. I have used the same one for most sites for many years.
lcaillo is online now  
post #7 of 32 Old 12-08-09, 09:29 AM
Shackster
Robert
 
Join Date: Nov 2009
Location: mechanicsville , MD
Posts: 38
Re: "How To Check The Hours Used on Your Plasma" :

Want to make sure this Pioneer KRP 600m I got today is not a fake-- heard there were some out there- did not buy it from pioneer authorized dealer
So MD TopGun is offline  
post #8 of 32 Old 12-08-09, 09:34 AM
HTS Administrator
 
lcaillo's Avatar
Tech Guru
 
Join Date: May 2006
Location: Gainesville, FL, USA
Posts: 10,991
Send a message via AIM to lcaillo
Re: "How To Check The Hours Used on Your Plasma" :

A fake? I have never heard of fake PDPs.

Looking for me, just google my username. I have used the same one for most sites for many years.
lcaillo is online now  
post #9 of 32 Old 12-08-09, 09:52 AM
Shackster
Robert
 
Join Date: Nov 2009
Location: mechanicsville , MD
Posts: 38
Re: "How To Check The Hours Used on Your Plasma" :

that's good news-- Now I got to get a hold of Turbe to order my patch- feel more relaxed now-thanks
So MD TopGun is offline  
post #10 of 32 Old 12-09-09, 03:37 AM
HTS Administrator
 
lcaillo's Avatar
Tech Guru
 
Join Date: May 2006
Location: Gainesville, FL, USA
Posts: 10,991
Send a message via AIM to lcaillo
Re: "How To Check The Hours Used on Your Plasma" :

You might have warranty coverage issues if you bought it from an unauthorized dealer, but I doubt it unless the set was previously sold, a refurb, or something else fishy. These are questions for your dealer and Pioneer, however.

Looking for me, just google my username. I have used the same one for most sites for many years.
lcaillo is online now  
Reply

Bookmarks

Tags
"how , check , hours , plasma"

Quick Reply
Message:
Options

Register Now




PLEASE COMPLETE ALL REQUIRED FIELDS BELOW... THANKS!

REQUIRED FIELDS ON THIS PAGE
YOU MUST COMPLETE ALL OF THESE

Username
Password
Confirm Password
Email Address
Confirm Email Address
Random Question
Random Question #2




User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
PLEASE READ BELOW PRIOR TO ENTERING AN EMAIL ADDRESS!

ATTENTION!

YOU MUST ACTIVATE YOUR ACCOUNT!

Activation requires you reply to an email we will send you after you register... if you do not reply to this email, you will not be able to view certain areas of the forum or certain images... nor will you be able download software.

AN INVALID EMAIL ADDRESS WILL CAUSE YOUR ACCOUNT TO BE DELETED!

See our banned email list here: Banned Email List

We DO NOT respond to spamcop, boxtrapper and spamblocker emails... please add @hometheatershack DOT com to your whitelist prior to registering or you will get nowhere on your registration.


Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML is not allowed!
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

 


For the best viewing experience please update your browser to Google Chrome